Showing 2273–2288 of 2574 results
PHY-MECH-60 LINEAR AIR TRACK APPARATUS
SSI-PHY-MECH-60
To exlplore the concepts of mechanics involving linear motion on a near frictionless surface, such as acceleration, collisions (elastic / inelastic), explosions, conservation of momentum and simple harmonic motion etc. Air track, the principal component of the apparatus, comprises of specially designed, rugged, anodized, aluminum alloy extrusion providing a straight
PHY-MECH-61 LINEAR AIR TRACK APPARATUS, ECONOMICAL
SSI-PHY-MECH-61
A simple and economical apparatus with all functionalities. One end of the track has an air inlet tube connection for compressed air supply. The track also has a 0-200cm scale graduated in millimeters for measuring distances and recording positions. Constructed to the demanding standards and features typical of more expensive
PHY-MECH-62 LINEAR AIR TRACK APPARATUS, ACCESSORIES
SSI-PHY-MECH-62
Accessories for Linear Air Track Apparatus Complete set includes following accessories large vehicle 2 small vehicles Launching cradle Elastic Collider Non-elastic collider pair Pulley wheel Scale pan and masses Constant level cushion block 1 reel of nylon thread Pack of elastic bands Set of fixing nuts
PHY-MECH-63 AIR BLOWER FOR LINEAR AIR TRACK APPARATUS,
SSI-PHY-MECH-63
Air Blower: Specifically designed for use with the apparatus, provides constant air pressure. Significantly quieter than other sources, yet powerful enough to easily float fully-loaded gliders. Supplied complete with flexible hose pipe and mains lead attached to it. Operates on 220-240VAC, 50Hz.
PHY-MECH-65 FORCE, MOTION & DYNAMICS KIT
SSI-PHY-MECH-65
This apparatus comprises a high quality aluminium profile bench with a built in scale to make a variety of measurements. The system provides a highly motivational approach to conducting dynamics experiments. Investigate the effect of different accelerating forces on different masses, elastic and inelastic collisions between two trolleys, acceleration on
PHY-MECH-66 MECHANICS KIT
SSI-PHY-MECH-66
The components provided in the kit are easy to set up and enable the user to perform a wide range of experiments in mechanics, e.g. distance measurements, the measurement of velocity and acceleration, verification of Newton’s laws of motion, principle of conservation of energy and momentum, and measurement of acceleration
PHY-MEPT-01 ENERGY TRANSFER APPARATUS (MALVERN) (MOUNTED MOTOR FOR SOLAR CELL)
SSI-PHY-MEPT-01
Dimensions:-95x75mm (lxw) operating:-0.8 volt DC demonstrate the conversion of solar energy and hence to mechanical energy. A compact and low consumption mounted on a base.
PHY-MEPT-03 ENERGY TRANSFER APPARATUS (MALVERN) (LAMP UNIT TRIPLE)
SSI-PHY-MEPT-03
Comprises three MES lamp sockets connected in parallel with a pair of 4mm terminals. For use with motor/generator to give an indication of their output when used as dynamos. Supplied with three lamps 3.5V, 0.25A.
PHY-MEPT-04 ENERGY TRANSFER APPARATUS (MALVERN) LAMP UNIT TRIPLE(DELUXE)
SSI-PHY-MEPT-04
Comprises three MES lamp sockets connected in parallel with a pair of 4mm terminals. For use with motor/generator to give an indication of their output when used as dynamos. Supplied with three lamps 3.5V, 0.25A. Better quality. All three lamp holders enclosed in insulated cover with only their mouths visible for fixing lamps.
PHY-MEPT-05 ENERGY TRANSFER APPARATUS (MALVERN) (MOTOR GENERATOR)
SSI-PHY-MEPT-05
For use as a driving unit or dynamo. Comprises a low voltage, permanent magnet, DC motor, provided with a pulley. Supplied with driving belt.
PHY-MEPT-06 ENERGY TRANSFER APPARATUS (MALVERN)(LINE SHAFT UNIT)
SSI-PHY-MEPT-06
For showing the conversion from electrical energy, via mechanical, to potential energy by winding up a mass on a cord. One end of the shaft carries pulley, and the other shaft end overhangs the base. Fitted with a cord anchoring collar to enable mass to be wound up. Supplied complete with driving belt.
PHY-MEPT-07 ENERGY TRANSFER APPARATUS (MALVERN)(TURBINE PUMP UNIT)
SSI-PHY-MEPT-07
For use as a water turbine to drive a generator producing electricity or as a pump driven by a motor and raising a head of water to produce potential energy. The rotor encased in a cast metal housing with a clear acrylic front, has eight bucket blades. Two inlet tubules (for turbine and
PHY-MEPT-08 ENERGY TRANSFER APPARATUS (MALVERN)(SPRING UNIT)
SSI-PHY-MEPT-08
For showing potential energy stored in a wound-up steel spring and its conversion to electrical energy by driving a dynamo and lighting a lamp. May also be used to wind up a mass on a cord showing the change from potential energy to kinetic and back to potential in the raised mass. The steel
PHY-MEPT-09 ENERGY TRANSFER APPARATUS (MALVERN)(HEAD OF WATER UNIT)
SSI-PHY-MEPT-09
For use with turbine pump unit to provide an open or closed system in demonstrating the conversion from electrical to kinetic energy in the pump and potential energy in the head of water. Supplied complete with two glass basins and shaped glass tubes. The upper platform has a hole to it sallow use as
PHY-MEPT-10 ENERGY TRANSFER APPARATUS (MALVERN)(HAND WHEEL DRIVING UNIT)
SSI-PHY-MEPT-10
Converts human muscular energy to other forms of energy. For use in driving dynamos, line shafts, fly wheels, pumps etc. The driving and output pulleys are both of 75mm dia. and the intermediate pulley is 20mm dia. giving a step-up ratio of 3.75.
PHY-MEPT-11 ENERGY TRANSFER APPARATUS (MALVERN)(MOUNTED LAMP 12V 24W)
SSI-PHY-MEPT-11
A 12V 24W SBC bulb in a metal socket mounted on a folded metal base 100×63mm approx. with a pair of 4mm sockets. The power rating of the bulb has been chosen so that when it is placed in front of the solar cell, sufficient power is produced to run the motor effectively whilst avoiding