Showing 2097–2112 of 2574 results
PHY-FLU-041 SIPHON BAROMETER
SSI.PHY.FLU.041
A low cost, simple barometer yet having sufficient accuracy. The whole column of mercury is clearly visible in the glass tube. Barometer scale is graduated, one side from 23cm – 31cm and another side 580mm – 790mm. Vertical sliding zero point adjustment is carried by a screw clamp attached to
PHY-HEAT-01 CONDUCTIVITY APPARATUS INGEN HAUSZ'S
SSI-PHY-HEAT-01
Five rods, one each of aluminium, brass, copper, zinc and iron, embedded along one side of a metal tank, size 150 x 90 x 100mm. Rates of melting compared by placing wax on the ends of the different rods thus demonstrates rates of conductivity in the different metals.
.
PHY-HEAT-05 JOULES CALORIMETER COPPER
SSI-PHY-HEAT-05
Double vessel calorimeter with inner smaller vessel of size 75×50mm (height × diameter) positioned inside another copper vessel of size 100×75mm (height × diameter) and is surrounded completely with felt except on top to provide adequate thermal insulation. The vessels have a bakelite lid for thermal insulation at the top
PHY-HEAT-06 CALORIMETER SET ALL COPPER
SSI-PHY-HEAT-06
Double vessel calorimeter with inner smaller vessel of size 75×50mm (height × diameter) positioned inside another copper vessel of size 100×75mm (height × diameter) and is surrounded completely with felt except on top to provide adequate thermal insulation. The vessels have a copper lid at the top and a hole
PHY-HEAT-07 CALORIMETER STIRRER COPPER
SSI-PHY-HEAT-07
Used for stirring the contents of the calorimeter to ensure uniform mixing for proper heat exchange. Made of metal wire of 1.5mm diameter, with insulated plastic handle at upper end and circular loop at bottom.
PHY-HEAT-10 JOULES COLORIMETER ALUMINIUM
SSI-PHY-HEAT-10
Double vessel calorimeter with inner smaller vessel of size 75×50mm (height × diameter) positioned inside another Aluminium vessel of size 100×75mm (height × diameter) and is surrounded completely with felt except on top to provide adequate thermal insulation. The vessels have a bakelite lid for thermal insulation at the top
PHY-HEAT-11 CALORIMETER STIRRER ALUMINIUM
SSI-PHY-HEAT-11
Used for stirring the contents of the calorimeter to ensure uniform mixing for proper heat exchange. Made of metal wire of 1.5mm diameter, with insulated plastic handle at upper end and circular loop at bottom.
Material type : Aluminium
PHY-HEAT-12 STEAM GENERATOR SET
SSI-PHY-HEAT-12
Useful for experiments involving heating by means of steam or where continuous source of steam is needed. Made of heavy gauge aluminium sheet to provide sturdiness and durability for withstanding high boiling pressures, with riffled nozzle for steam outlet. Consists of boiler assembly, two rubber stoppers – one solid and
PHY-HEAT-13 STEAM BOILER COPPER
SSI-PHY-HEAT-13
Steam Generator with a 1.5L capacity, made from quality copper. General use for a this steam generator is for creating high pressure and gas for physics and chemistry such as thermal expansion (linear rod expansion) type experiments. 9.5" long, 4.75" base diameter, top opening of 1.25", small spout of 1.5"
PHY-HEAT-14 STEAM BOILER GI SHEET
SSI-PHY-HEAT-14
Steam Generator with a 1.5L capacity, made from GI Sheet. General use for a this steam generator is for creating high pressure and gas for physics and chemistry such as thermal expansion (linear rod expansion) type experiments. 9.5" long, 4.75" base diameter, top opening of 1.25", small spout of 1.5"
PHY-HEAT-15 STEAM BOILER COPPER MODERN DESIGN
SSI-PHY-HEAT-15
Copper cylindrical vessel 180 x 115 mm with steam vent and a vertical tube terminating in chute passing through side of vessel. A brass tube sliding fit in the central tube, with lower angle cut to seal the chute, enables heated material to be transferred to calorimeter without loss of
PHY-HEAT-16 STEAM TRAP GLASS
SSI-PHY-HEAT-16
Cylindrical steam glass trap with tubes on each end. Made from high quality borosilicate glass. The unit is 7.5" in total length with a 1" diameter at the center of the body and .5" inner diameter at the opening of each of the 1.25" stems. Strain Point -515°C | Annealing
PHY-HEAT-18 MELTING POINT APPARATUS SIMPLE
SSI-PHY-HEAT-18
Comprises an aluminium cylinder with an obliquely drilled hole at its top for accommodating thermometers. When a very thin layer of the substance, whose melting point is to be determined, is sprinkled on top of the block and is gently heated, the temperature at which substance melts can be directly
PHY-HEAT-19.1 CONVECTION TUBE
SSI-PHY-HEAT-19.1
This is a glass tube that is bent into a square shape with a funnel-shaped opening on one side. The tube is filled with water and a pinch of potassium permanganate or a drop of food coloring is added to the opening. The tube is then heated in the corner