Showing 1729–1744 of 2574 results
PCL-E661 DIGITAL CONTROL SYSTEM TRAINER
PCL-661
PCL-E661 DIGITAL CONTROL SYSTEM TRAINER
SCOPE OF LEARNING:
• Study of P, PI, PID Controller
• Study of Sampling Period variation.
• Identification of controlled process.
PCL-E663 LIGHT INTENSITY CONTROL SYSTEM TRAINER
PCL-663
PCL-E663 LIGHT INTENSITY CONTROL SYSTEM TRAINER
SCOPE OF LEARNING:
o Study of Light Intensity Control.
o Characteristics of Light Panel and Light Sensor Block.
o Study of Single loop feedback control.
o Evaluation of dynamic behavior.
PCL-E727 RELAY CONTROL SYSTEM TRAINER
PCL-727
PCL-E727 RELAY CONTROL SYSTEM TRAINER
SCOPE OF LEARNING:
• Study of the relay characteristics and display of the same on CRO for different values of hysteresis and dead zones.
• Study of the effect of hysteresis on system stability.
• Phase plane analysis of relay control system for various values of Hysteresis and Dead
PCL-E728 MAGNETIC AMPLIFIER KIT (SERIES & PARALLEL)
PCL-728
PCL-E728 MAGNETIC AMPLIFIER KIT (SERIES & PARALLEL)
Amplification is the control of a larger output quantity by the variation of a smaller input quantity. Such amplification can be performed by storable reactors connected either in series or in parallel.. This set up consists two such reactors, AC and DC power supply,
PCSM-280 SINGLE PHASE CAPACITOR START INDUCTION MOTOR (CUT MOTOR)
PCSM-280
PCSM-280 SINGLE PHASE CAPACITOR START INDUCTION MOTOR (CUT MOTOR)
ABOUT MOTOR:
A Capacitor Start Motors are a single phase Induction Motor that employs a capacitor in the auxiliary winding circuit to produce a greater phase difference between the current in the main and the auxiliary windings. The name capacitor starts itself shows
PCSM-297 THREE PHASE SLIP RING INDUCTION MOTOR (MOTOR)
PCSM-297
PCSM-297 THREE PHASE SLIP RING INDUCTION MOTOR (MOTOR)
ABOUT MOTOR:
The three phase induction motor is the most widely used electrical motor. Almost 80% of the mechanical power used by industries is provided by three phase induction motors because of its simple and rugged construction, low cost, good operating characteristics, the absence
PCSM-301 SINGLE PHASE SPLIT POLE MOTOR (CUT MOTOR)
PCSM-301
PCSM-301 SINGLE PHASE SPLIT POLE MOTOR (CUT MOTOR)
ABOUT MOTOR
The starter winding has a capacitor incorporated which makes the single-phase motor a self-starting one. Read on to learn about the different types of widely used capacitor-motors
The single-phase induction motor can be made to be self-starting in numerous ways. One often-used method
PCSM-305 SINGLE PHASE AC REPULSION INDUCTION MOTOR (CUT SECTION)
PCSM-305
PCSM-305 SINGLE PHASE AC REPULSION INDUCTION MOTOR (CUT SECTION)
ABOUT MOTOR
A repulsion motor is a type of electric motor which runs on alternating current (AC). It was formerly used as a traction motor for electric trains (e.g. SR Class CP and SR Class SL electric multiple units) but has been superseded
PCSM-378 THREE PHASE SQUIRREL CAGE INDUCTION MOTOR (CUT MOTOR)
PCSM-378
PCSM-378 THREE PHASE SQUIRREL CAGE INDUCTION MOTOR (CUT MOTOR)
ABOUT MOTOR:
A squirrel-cage rotor is the rotating part of the common squirrel-cage induction motor. It consists of a cylinder of steel laminations, with aluminum or copper conductors embedded in its surface. In operation, the non-rotating stator winding is connected to a current
PCSM-380 DC SHUNT MOTOR (CUT MOTOR)
PCSM-380
PCSM-380 DC SHUNT MOTOR (CUT MOTOR)
ABOUT MOTOR:
The shunt wound DC motor falls under the category of self excited DC motors, where the field windings are shunted to, or are connected in parallel to the armature winding of the motor, as its name is suggestive of. And for this reason both
PCSM-422 THREE PHASE SYNCHRONOUS INDUCTION MOTOR (CUT MOTOR)
PCSM-422
PCSM-422 THREE PHASE SYNCHRONOUS INDUCTION MOTOR (CUT MOTOR)
ABOUT MOTOR:
Electrical motor in general is an electro-mechanical device that converts energy from electrical domain to mechanical domain. Based on the type of input we have classified it into single phase and 3 phase motors. Among 3 phase motors, we mostly sue induction
PCSM-452 DC COMPOUND MOTOR (CUT SECTION)
PCSM-452
MOTOR SPECIFICATIONS: • DC Compound Motor 1HP • Operating Voltage:230V • Type: DC • RPM: 1440 RPM. • Wattage: 0.75KW • Terminations: 5 BTI 15 Terminals • Shaft: Single • Frame:132 • B3 • SPDP • 1P23 • 1C01 • Solid Yoke Extension • Fitted on Metal Base.
PCSM-588 PERMANENT MAGNET DC MOTOR (PMDC) MOTOR (CUT MOTOR)
PCSM-588
PCSM-588 PERMANENT MAGNET DC MOTOR (PMDC) MOTOR (CUT MOTOR)
ABOUT MOTOR:
• In a PMDC motor, permanent magnets (located in stator) provide magnetic field, instead of stator winding. The stator is usually made from steel in cylindrical form. Permanent magnets are usually made from rare earth materials or neodymium.
• The rotor is
PCT-E040 AMPLITUDE MODULATION AND DEMODULATION TRAINER
PCT-E040
PCT-E040 AMPLITUDE MODULATION AND DEMODULATION TRAINER SCOPE OF LEARNING: • Amplitude Modulation • Amplitude Demodulation • TECHNICAL SPECIFICATIONS: Generator: • On Board Carrier Generator 100KHz • On Board Modulating Signal Oscillator 0-1KHz Power Supply: • Fixed DC Power Supplies +15V DC, 250mA • Operated on Mains power 230V, 50Hz +10%
PCT-E065 TRANSMISSION LINE TRAINER (4MHz FREQUENCY GENERATOR)
PCT-E065
SCOPE OF LEARNING: • Measurement with 1) Matched, 2) Short, 3) Open end of the line • Measurement of line properties • Measurement of line attenuation • Frequency characteristics of line • Input impedance of the line • Measurement of stationary waves • Phase shift along the line • Fault
PCT-E163 DELTA MODULATION AND DEMODULATION TRAINER
PCT-E163
SCOPE OF LEARNING: • Delta Modulation • Delta Demodulation TECHNICAL SPECIFICATIONS: Generator: • Sampling Frequency : 20KHz. Square wave using IC 555 • Modulating Signal : 250Hz Sine wave using IC TL084 with variable amplitude up to 3 Vpp Power Supply: • Fixed DC Power Supplies +12V,+5V DC, 250mA •